10 exam-style questions with answers and explanations, straight from our 1,030-question bank. Tap an answer to check yourself. When you're ready, take the scored version in the free practice test.
The ASSI exam has 60 questions and runs 1 hours.
These 10 free ASSI questions are organized by exam domain, so you can see how each part of the Asphalt Shingle Systems Installer blueprint is tested. Reveal the answer and explanation under each question.
The manufacturer's clearance chart requires 16 feet below the working surface for the proposed personal fall-arrest system, anchorage, and worker configuration. The measured distance from that surface to a lower roof is 12 feet. The anchorage and harness pass inspection. Before using this setup, the crew needs to:
Correct answer: C - Select an approved fall-protection system that fits the available clearance.
A crew will work on a 7:12 roof, 14 feet above grade. A verified compliant guardrail system with toeboards protects every exposed edge; access points and roof openings are also protected. Neither the employer nor the project requires an additional fall-protection method. Under OSHA's steep-roof provisions, which statement is correct?
Correct answer: C - The guardrails meet the steep-roof edge-protection requirement on their own.
A roof takeoff lists the main roof as 800 square feet of horizontal projection at a 9:12 slope. An attached porch adds 300 square feet measured directly on its sloping roof surface. The 9:12 slope multiplier is 1.25. What total roof-covering area belongs in the estimate before any waste allowance?
Correct answer: A - 1,300 square feet
A pneumatic roofing nailer jams. The compressor motor is switched off, but the connected hose remains charged. Opening the jam-release mechanism is the next servicing step. What must the installer do first?
Correct answer: B - Isolate and depressurize the nailer using its service instructions.
After a windstorm, an installer examines laminated shingles that pulled free of their fastening points. Each shingle had the specified number and length of nails, driven square and flush into sound decking. The nails were above the marked fastening zone and missed the required overlap of the laminated layers. Which attachment defect best explains the damage?
Correct answer: B - High nails left the laminated layers inadequately secured.
The installation instructions for a synthetic underlayment require at least 4 inches of sidelap and 6 inches of endlap. Cap-fastener spacing must not exceed 12 inches in the field or 6 inches along laps. All caps are seated flat, and the sheet is undamaged. Which inspection finding prevents acceptance?
Correct answer: B - The lap fasteners are 8 inches on center.
A deck that was damp at dawn is now sound, secure, smooth, clean, dry, and frost-free. The specified membrane requires both air and substrate temperatures of at least 45°F; readings are 55°F and 50°F, respectively. The project's maximum wood-moisture reading is 15%; the specified meter, correctly set and checked, reads 13%. The required primer is dry. How should these findings affect installation?
Correct answer: D - Apply the specified membrane while the verified conditions remain suitable.
On several cold mornings following a dry week, droplets appear across the underside of both roof slopes and on exposed nail tips. The moisture diminishes as the attic warms. There is no snow on the roof, and a bathroom exhaust duct terminates inside the attic. Which mechanism best accounts for this pattern?
Correct answer: A - Condensation of indoor moisture on the cold roof deck.
Water testing traces runoff down a roof-to-sidewall intersection and behind the siding where the intersection ends just above the gutter. The step flashings are intact and correctly interleaved, their wall legs are properly protected, and the gutter drains freely. The lower termination has no diverter. Select the correction that redirects the identified water path.
Correct answer: D - Integrate a kick-out to discharge the sidewall runoff into the gutter.
An approved ventilation design requires total net free ventilating area (NFVA) at a 1:300 ratio to the 1,500-square-foot attic floor, divided equally between intake and exhaust. The exhaust allocation is already met. Each intake vent has a 10-by-10-inch face but a rated NFVA of 60 square inches. Four matching intake vents are installed, unobstructed, and serving this attic. How many additional matching intake vents are needed?
Correct answer: A - 2 additional vents
The ASSI exam also covers these domains. Drill them in the full free practice test:
The full bank has 1,020 more ASSI questions with explanations.
Continue in the free practice test →
View plans